Product Overview
About: Taramps BASS 400 Class D Car Amplifier (Taramps Authorized Canadian Dealer)
The BASS 400 amplifier is the perfect choice for those who want superior performance in sub-bass and bass frequencies. With 400W RMS of power and 1 Ohm or 2 Ohm options, it covers a frequency range of 8 Hz to 250 Hz, ideal for getting the most out of your subwoofers. Its RCA and WIRE audio inputs offer flexibility of use, being compatible with most players on the market, including original multimedia players, without the need for adapters.
This amplifier comes equipped with gain adjustment (0.2 to 4 V), crossover with subsonic control from 8 to 30 Hz and Low Pass from 55 to 250 Hz. In addition, the variable Bass Boost allows you to select the center frequency between 35 and 55 Hz, increasing bass by up to 12 dB for a more intense sound experience.
The aluminum construction provides durability and excellent heat dissipation. And for even more convenient control, the BASS 400 is compatible with the *Monitor Level Remote accessory, which can be easily installed on the car dashboard, ensuring convenient and instant volume adjustment.
Discover even more impactful bass with the new BASS 400 from Taramps.
*The Monitor Level Remote accessory (sold separately) features three LED indicators: On, Clip, and Protect. When used with the BASS 400 amplifier, only the On (blue) LED will be activated, as the amplifier does not have Clip and Protect indicators.
Technical Information:
|
BASS 400 - 1 Ohm |
BASS 400 - 2 Ohms |
|
| Nominal Power | @14.4VDC - 1 Ohm: 400 Watts RMS | @ 13.8 VDC - 2 Ohms: 400 Watts RMS @ 13.8 VDC - 4 Ohms: 214 Watts RMS |
| Operation Class | Class D | Class D |
| Minimum Output Impedance | 1 Ohm / 4 Ohms | 2 Ohms |
| Number of Channels | 01 | 01 |
| Input Sensitivity | 320mV (RCA) / 6V (WIRE) | 320mV (RCA) - 6V (FIO) - LEVEL 100% |
| Signal to Noise Ratio | >90dB | > 90dB |
| Frequency Response | 8Hz ~ 250Hz (-3dB) | 8Hz ~ 250Hz (-3dB) |
| Crossover | Subsonic Crossover: 8Hz~30Hz (-12dB/8ª) Variable | |
| Crossover High Pass (HPF) | 8Hz ~ 30Hz (-12dB/8ª) Variable | |
| Crossover Low Pass (LPF) | 55Hz ~ 250Hz (-12dB/8ª) Variable | 55Hz ~ 250Hz (-12dB/8ª) Variable |
| Bass Boost | 35 ~ 55Hz (0 ~ +12dB) Parametric | Parametric, Freq.: 35Hz ~ 55Hz / Boost: 0 ~ +12dB |
| Efficiency | 82% | 82% |
| Input Impedance | 10K Ohms (RCA) / 1K Ohms (WIRE) | 10K Ohms (RCA) / 1K Ohms (WIRE) |
| Protection System | Output short circuit / Thermal Protection | Thermal Protection and Output Short Circuit |
| Minimum Supply Voltage | 8 VDC | 8 VDC |
| Maximum Supply Voltage | 16 VDC | 16 VDC |
| Consumption at Rest | 0.5A | 0.5A |
| Maximum Music Consumption | @ 14.4VDC: 17.5A | @13.8 VDC - 17.5A |
| Maximum Consumption in Sinusoidal Signal | 35A | 35A |
| Dimensions (W x H x D) | 5.27" x 1.57" x 5.43" (134 x 40 x 138 mm) | 5.28" x 1.57" x 5.43" (134 x 40 x 138mm) |
| Weight | 1.26 lb (0.57 Kg) | 1.25lb (0,57kg) |
| EAN | 7908706601565 |
7898556845915 |
- Do not mount amplifier to speaker box. Cyclic Vibrational Failure is #1 fail rate of amplifiers and these are lighter than most so their potential is higher if not followed.
- Do not wire this amplifier lower than 1ohm nominal Impedance. (Equivalent to ~0.7 ohms DCR or Resistive measurement via DMM).
- Do not clip amplifier above 15.0v for extended periods of time
- Do not drive amplifier into clipping + protection for extended periods of time (exceeding 20% THD)
