Product Overview
About: Taramps MD 8000.1 High Power Car Amplifier (Taramps Authorized Canadian Dealer)
The MD 8000.1 amplifier is carefully developed with state-of-the-art technology, offering unique efficiency and performance for automotive audio systems. Classified as Mono, it has a maximum power of 8.000 watts RMS, running at a 1-ohm or 2-ohm impedance, with a single 8,000 watts RMS channel. This amplifier is FULL-RANGE, operating on all frequencies in the right measure. It is an amplifier classified as mono, has a channel with a maximum power of 8000 Watts RMS. Welcome to the sound world of Taramps.
Technical Information:
| MD 8000.1 – 1 OHM | MD 8000.1 – 2 OHMS | |
| OPERATION CLASS | Class D | Class D |
| NUMBER OF CHANNELS | 01 | 01 |
| MAXIMUM POWER | @ 12,6 VDC - 1 OHM: 8000W RMS @ 12,6 VDC - 2 OHMS: 5120W RMS |
@ 12,6 VDC - 2 OHMS: 8000W RMS @ 12,6 VDC - 4 OHMS: 4800W RMS |
| INPUT SENSITIVITY | 0.22V ~ 4V | 0.22V ~ 4V |
| SIGNAL TO NOISE RATIO | >90dB | >90dB |
| FREQUENCY RESPONSE | 10Hz ~ 8KHz (-3dB) | 10Hz ~ 8KHz (-3dB) |
| CROSSOVER HIGH PASS (HPF) | 10Hz ~ 90Hz(-12/8ª) Variable | 10Hz ~ 90Hz (-12dB/8ª) Variable |
| CROSSOVER LOW PASS (LPF) | 90Hz ~ 10KHz (-12dB/8ª) Variable | 90Hz ~ 10KHz (-12dB/8ª) Variable |
| BASS BOOST | Freq: 35Hz to 55Hz Boost: 0 ~ 10dB (50Hz) |
Freq.: 35Hz ~ 55Hz Boost: 0 ~10dB |
| EFFICIENCY | 82% | 85% |
| INPUT IMPEDANCE | 10K Ohms | 10K Ohms |
| OUTPUT IMPEDANCE | 1 Ohm | 2 Ohms |
| PROTECTION SYSTEM | Short-Circuit to Output, short on output compared to GND, Low impedance at output, High/Low supply voltage and Thermal protection | Short-Circuit to Output, Short on output compared to GND, Low impedance at output, High/Low supply voltage and Thermal protection. |
| MIN. SUPPLY VOLTAGE | 9.5VDC | 9.5VDC |
| MAXIMUM POWER SUPPLY VOLTAGE | 17VDC | 17VDC |
| CONSUMPTION AT REST | 2.90A | 2.90A |
| MAXIMUM MUSIC CONSUMPTION | 387A | 374A |
| MAXIMUM CONSUMPTION IN SINUSOIDAL SIGNAL | 774A | 748A |
| DIMENSIONS (H X W X D) | 8.98" x 2.76" x 17.5" (228 x 70 x 446 mm) | 8.98" x 2.76" x 17.5" (228 x 70 x 446 mm) |
| WEIGHT | 12.34lb (5.60Kg) | 12.34lb (5.60Kg) |
| EAN | 7898556844468 | 7898556848893 |
Precautions:
- Do not mount amplifier to speaker box. Cyclic Vibrational Failure is #1 fail rate of amplifiers and these are lighter than most so their potential is higher if not followed.
- Do not wire this amplifier lower than 1ohm nominal Impedance. (Equivalent to ~0.7 ohms DCR or Resistive measurement via DMM).
- Do not clip amplifier above 15.0v for extended periods of time
- Do not drive amplifier into clipping + protection for extended periods of time (exceeding 20% THD)
