Product Overview
About: Taramps T9.000 Chipeo 9K Monoblock Amplifier (Taramps Authorized Canadian Dealer)
Feel the difference with the Taramps T 9.000 Chipeo, an amplifier that redefines the standards of musical performance. Available in 1 or 2 Ohm versions, this fantastic amplifier offers an impressive 9000 W RMS at 12.6 Volts, and can reach an astonishing 11,000 WRMS at 14.4 Volts. With a wide frequency response of 5Hz to 5kHz, it covers sub-bass, bass, mid-bass and mid. Experience much more strength, quality, efficiency and resistance, and take your sound experience to a new level.
Technical Information
| T9.000 Chipeo - 1 Ohm | T9.000 Chipeo - 2 Ohms | |
| Nominal Power | Nominal Power@12.6VDC 1 Ohm: 9000W RMS 2 Ohms: 5445W RMS Nominal Power@13.8VDC 1 Ohm: 10000W RMS 2 Ohms: 6100W RMS Nominal Power@14.4VDC 1 Ohm: 11000W RMS 2 Ohms: 6710W RMS | Nominal Power@12.6VDC 2 Ohms: 9000W RMS 4 Ohms: 5445W Nominal Power@13.8VDC 2 Ohms: 10000W RMS 4 Ohms: 6100W RMS Nominal Power@14.4VDC 2 Ohms: 11000W RMS 4 Ohms: 6710W RMS |
| Number of Channels | 01 | 01 |
| Input Sensitivity | 220mV ~ 4V RMS | 220mV ~ 4V RMS |
| Signal to Noise Ratio | >90dB | >90dB |
| Frequency Response | 5Hz ~ 5KHz (-3dB) | 5Hz ~ 5KHz (-3dB) |
| Efficiency | 1 Ohm: 79% | 2 Ohms: 84% |
| Input Impedance | 10K Ohms | 10K Ohms |
| Protection System | Short-circuit on output and in relation to GRD, low impedance, high/low voltage and thermal protection | Short-circuit on output and in relation to GRD, low impedance, high/low voltage and thermal protection |
| Minimum Supply Voltage | 9VDC | 9VDC |
| Maximum Supply Voltage | 17VDC | 17VDC |
| Consumption at Rest | 1 Ohm: 3.70A | 2 Ohms: 1.50A |
| Maximum Music Consumption | @12,6VDC: 1 Ohm: 450A | @12,6VDC: 2 Ohms: 423A |
| Maximum Consumption in Sinusoidal Signal | 1 Ohm: 900A | 2 Ohms: 846A |
| Dimensions (W x H x D) | 8.98" x 2.52" x 17.56" (228 x 64 x 446 mm) | 8.98" x 2.52" x 17.56" (228 x 64 x 446 mm) |
| Weight | 12.79 lb (5.80 Kg) | 12.79 lb (5.80 Kg) |
| EAN | 7908706600797 | 7908706600780 |
Precautions
- Do not mount amplifier to speaker box. Cyclic Vibrational Failure is #1 fail rate of amplifiers and these are lighter than most so their potential is higher if not followed.
- Do not wire this amplifier lower than 1ohm nominal Impedance. (Equivalent to ~0.7 ohms DCR or Resistive measurement via DMM).
- Do not clip amplifier above 15.0v for extended periods of time
- Do not drive amplifier into clipping + protection for extended periods of time (exceeding 20% THD)
